ServicesFrame Straightening
Frame Straightening in Mendota
After a hard hit, the structure under the panels can shift by a fraction of an inch and still change how your car drives and protects you. We measure against factory dimensions, straighten or replace what is damaged, and prove the result before the body work begins.

What frame straightening fixes
Most cars on the road today are unibody: the floor, rails and pillars form one welded shell instead of sitting on a separate frame. Trucks and many larger SUVs still use a full ladder frame. Either way, a collision can push mounting points out of position. Doors stop closing cleanly, panel gaps open up, and the car pulls or eats tires no matter how often it is aligned.
Frame straightening returns those points to where the manufacturer put them. Our technicians follow the training behind our I-CAR Platinum certified status, which matters most here, because modern high-strength steels behave differently under heat and tension than older mild steel.
We look at the repair over the life of your vehicle. A cheaper quick pull that leaves a rail a few millimeters off often costs more later in tires, suspension parts and lost trade-in value. We would rather tell you that plainly now.
What the repair includes
Full structural measurement
We measure control points across the underbody and upper body and compare them with published factory dimensions. You see the numbers, not a guess.
Controlled pulls on a frame bench
Your car is anchored at its pinch welds or frame and pulled in several directions at once, slowly, so metal returns along the path it moved. We stop and re-measure between pulls.
Bend or kink decision
A smooth bend can usually be straightened. A sharp kink in high-strength steel often cannot be restored safely, so that section is replaced at factory seams instead.
Sectioning and welding where needed
When a rail or apron has to be replaced, we follow the manufacturer's repair procedure for cut locations and weld type. Corrosion protection goes back inside the new section.
Final verification
After straightening, we measure again and record the results. Suspension angles and sensor mounting points are checked before the car moves on to body and paint.
Signs your car may need frame work
Doors or hood that no longer line up
If a door needs a slam to latch or the hood sits higher on one side, the openings themselves may have moved.
Uneven gaps between panels
A gap that is wide at the top of a fender and tight at the bottom often points to a shifted mounting point rather than a bad panel.
Pulling after an alignment
When an alignment shop cannot bring the numbers into range, the suspension may be bolted to a structure that is out of place.
Tires wearing on one edge
Fast, uneven wear on a single tire after a collision is worth having measured before you buy another set.
Wrinkles under the car
Creases in the floor pan or rails, or cracked seam sealer, show the metal absorbed force and folded.
How a frame repair moves through our shop
- 1
Inspection and measurement
We look over the car, then put it on the bench and measure. This tells us whether the damage is structural and how far it reaches.
- 2
A clear estimate
You get a line-item estimate showing what will be straightened, what will be replaced and why. If an insurance claim is involved, we share the same findings with your adjuster.
- 3
Straightening and replacement
We pull in stages and check our work as we go. Parts too damaged to restore are sectioned out and replaced to procedure.
- 4
Measure, then hand off to body work
Once every point is within tolerance, we record the final numbers. Only then do panels, paint and refinishing begin, so the finish sits on a straight foundation.
What affects the cost of frame straightening
Frame work is priced by what the measurements show, not by how the outside looks. A small-looking dent can hide a shifted rail, and a crumpled fender can sit on a perfectly straight structure. We price after measuring so the estimate reflects the real repair.
- How far the damage travels
- A hit that stays in the bumper reinforcement is a different job than one that moves the front rails or the strut towers.
- Straighten or replace
- Bent sections can often be pulled. Kinked high-strength steel usually has to be replaced, which adds parts and welding time.
- Vehicle construction
- Unibody cars, full-frame trucks and models with aluminum structures each call for different methods and, sometimes, different equipment.
- Parts and procedures
- Some manufacturers require specific replacement parts or repair steps. Following them adds cost now and keeps the car behaving as designed later.
Frame straightening questions
Something not covered here? (559) 491-1778
Is a car with frame damage ever the same again?
When the structure is measured, straightened or replaced to factory dimensions and verified afterward, it can drive and protect you as intended. The key is proof. We record measurements before and after so you know where every point ended up.
Will frame damage make my insurance company total the car?
Not automatically. The decision depends on repair cost compared with the car's value. Our measurements give the adjuster accurate information, and our Insurance Claims page explains how we work alongside your insurer.
How long does frame straightening take?
Light pulls can be done in a day or two of shop time. Jobs that need sectioned parts take longer, mostly because of parts availability. We give you a realistic timeline once the car has been measured.
Why not just get an alignment instead?
An alignment adjusts suspension angles within a small range. If the points the suspension bolts to have moved, the alignment cannot correct it, and tires keep wearing unevenly.
Will frame damage hurt my resale value?
A collision history can affect value, but documented repairs to factory specifications help. Keep the measurement printouts and estimate with your records for the next buyer.
Have the structure checked before the panels go on
If your car was in a hard hit, measuring now protects the work that follows. Drivers from Mendota, Firebaugh and Kerman bring their cars to us for a straight answer on frame damage.